• Volt Meter
  
• Test Light
  
• 20ft Jumper Lead Set
  
• Bad Ground Indicator
  
• Continuity Tester

• Built-in Flash Light
  
• Short Circuit Indicator
  
• Relay and Component Tester
  
• All this, plus it’s 42 volt ready!

• Easy to read backlit Voltmeter allows you to read voltage at the tip eliminating
  wasted time running to your toolbox for a voltmeter!
  
• 42V Ready right out of the box prepares you for the future now!
  
• New gold plated, rugged connectors guaranty a secure hook-up every time.
  
• Standard 4mm cap ensures full compatibly with our Gold Series Lead Set as well
  as all other 4mm leads, plugs & jacks already in your tool box.

• When you connect the Power Probe to the car’s battery you have a multitude of
  testers at your finger tips.
  
• Press the rocker switch forward and you’ll have a hot lead for powering up electrical components like cooling fans, relays, press the switch rearward and you will have an instant ground lead.
  
• Simultaneously use the hot lead and the ground lead to activate components
  right in your hand.
  
• The polarity tester instantly identifies positive, negative and open circuits without
  having to re-polarize or reconnect hookup clips like with ordinary test lights.
  
• Power Probes circuit breaker helps you to follow and locate shorts fast without
  wasting fuses.
  
• Instantly check continuity of switches, relays and diodes.

• Constantly searching for a ground hook-up
  
• Reconnecting and repolarizing hook-up clips
  
• Stringing out jumper leads and hooking them up.
  
• Performing a time consuming voltage drop test.
  
• Removing and reassembling panels, molding and carpet.
  
• Running to the battery to test the test light itself.
  
• Circuits opening and making complete contacts without you being aware of it.
  
• Running to get a multimeter just to test continuity of a switch, relay, diode, wire, or
  fuse.
  
• Rigging up a wire to connect into the fuse socket of the car.

Tracing Open Circuits

• Signal is being received
  
• Signal is not being received here
  
• Signal stops at the point of wire separation

Tracing Short Circuits

• Beep-beep-beep
  
• Signal drops at the point of the short circuit
  
• Beep-beep-beep
  
• No matter what side of the circuit you test, the Receiver will indicate the direction to the short or ground (observe LED indicator).

Circuit Wiggle and flex test

• Wiggle and twist wires to check for intermittent conditions in circuits
  
• Sometimes it may be necessary to check for intermittent connection
  problems. The circuit wiggle and flex test allows you to wiggle, twist, pull,
  push and flex wires or connectors to observe a circuit change.

Locking the reception distance

• As you bring the receiver near the transmitting signal, the tone pulses will
  increase in ppm (pulses per minute). When you reach the desired distance,
  depress the POWER/Sensitivity button to lock the reception at the distance
  you prefer.

• Super flexible leads come in lengths of 1ft., 3ft., and 6ft.and are stackable
  giving the technician even greater flexibility.
  
• Two self centering piercing probes not only save finger tips but make wire
  piercing a snap.
  
• The large and small probes enable the technician to pierce wires from 28
  gauge to 8 gauge while assuring the wire is centered every single time.
  
• Our banana jacks, plugs and adapters are shrouded for added safety and
  standard sized 4mm ensuring compatibility with all circuit testing equipment.
  
  

• A Power Probe III
  
• Cigarette Lighter Adapter
  
• 9in. Extension Probe
  
• 2 AAA batteries
  
• Instructional DVD
  
• ECT-2000 Transmitter & Receiver
  
• Battery hook-up clips
  
• 20ft extension lead
  
• 3 fuse adapters & 1 universal adapter
  
• Instruction manual
  
• Blow mold case with organizer
  

PPLS01 Test Lead Set:

• 2 Piercing Probes
  
• 1-3-6ft Leads
  
• Alligator Clip
  
• 4mm Male Adapter
  
• 4mm Female Adapter
  
• Probe Tip
  
• Banana Jack Adapter